UMI Performance Transmission Crossmembers (2228-R) for a 1982-1992 Chevrolet Camaro and 1982-1992 Pontiac Firebird. UMI Performance 82-92 GM F-Body Torque Arm Relocation Kit- T5 & 700R4.
Years | Make | Model | Trim | ||
---|---|---|---|---|---|
1982-1982 | Chevrolet | Camaro | Z28 Indianapolis 500 Pace Car | ||
1982-1987 | Chevrolet | Camaro | Z28 | ||
1982-1987 | Chevrolet | Camaro | Sport | ||
1982-1986 | Chevrolet | Camaro | Berlinetta | ||
1985-1990 | Chevrolet | Camaro | Iroc-Z | ||
1987-1987 | Chevrolet | Camaro | LT | ||
1988-1988 | Chevrolet | Camaro | Base | ||
1989-1992 | Chevrolet | Camaro | RS | ||
1991-1992 | Chevrolet | Camaro | Z28 | ||
1992-1992 | Chevrolet | Camaro | Z28 Heritage Edition | ||
1992-1992 | Chevrolet | Camaro | RS Heritage Edition | ||
1982-1986 | Pontiac | Firebird | S/E | ||
1982-1992 | Pontiac | Firebird | Base | ||
1982-1992 | Pontiac | Firebird | Trans Am | ||
1989-1992 | Pontiac | Firebird | Formula | ||
1989-1992 | Pontiac | Firebird | Trans Am GTA | ||
1989-1989 | Pontiac | Firebird | Trans Am GTA SE |
The torque arm relocation kit from UMI Performance is designed to remove the front mounting point of the torque arm off the transmission and protect the tail shaft from damage. General Motors tail shaft mounted design works great for a stock driven vehicle however it is not designed to take abuse and hard launches. This set-up replaces your transmission cross member with a new stronger set-up with a built in torque arm mount. Each relocation kit is designed to fit a specific transmission and will work with virtually any stock style aftermarket torque arm as well as the factory torque arm. The relocation kit also features instant center adjustment by moving the front of the torque arm up or down. This unit is built using DOM mild steel tubing, 0.188” mild steel mounting plates and includes all appropriate hardware needed for the installation. The torque arm mount is machined from 0.250” thick mild steel and features a new clam shell for appropriately attaching the torque arm to the new cross member. This relocation kit will work with both the manual T5 and automatic 700R4 transmission. Please use the FAQ’s below for additional information. Q: What does this kit do? A: Our transmission cross member is supplied with a built in torque arm mount removing the torque arm from the transmission tail shaft and protecting the tail shaft from failure. Q: Does this new relocation kit reduce ground clearance? A: No, our cross member is designed to tuck tight against the vehicle chassis and will not effect vehicle ground clearance. Q: Which brand torque arms will this work with? A: This set-up will work with virtually any torque arm on the market as long as it bolts into the stock location. It will also work excellent with the stock torque arm when using a 1-piece bushing (item #3004).
There are no reviews yet.
IN STOCK - LOW UMI Performance 2401-BUMI Performance K-Members UMI Performance 82-92 GM F-Body Tubular K-member Coil Springs $699.99
|
IN STOCK Yukon Gear & Axle YG D44-373Yukon Gear & Axle Gear Sets - Dana Yukon Gear High Performance Replacement Gear Set For Dana 44 in a 3.73 Ratio |
IN STOCK Yukon Gear & Axle YDGGM7.5-3-28-SMYukon Gear & Axle Dura Grip Yukon Gear Dura Grip Positraction For GM 7.625in w/ 28 Spline Axles / 3.23+ |
IN STOCK Yukon Gear & Axle YZLABF-KITYukon Gear & Axle Zip Lockers Yukon Gear Zip Locker Bulkhead Fitting Kit |
IN STOCK - LOW Yukon Gear & Axle YMS8610Yukon Gear & Axle Seals Yukon Gear 7.2in GM 7.5in GM & 8.2in GM Pinion Seal |
IN STOCK - LOW McLeod Racing 75225McLeod Racing SS Pro Clutch Kits McLeod Super Street Pro Kit Chev V8 55-85 $325.00
|
IN STOCK - LOW Yukon Gear & Axle YC D706024-XYukon Gear & Axle Carrier Cases Yukon Gear Replacement Standard Open Carrier Case For Dana 44 / 30 Spline / 3.73 & Down / Bare |
IN STOCK - LOW Yukon Gear & Axle YPKD44-PC-SMYukon Gear & Axle Positraction Internals Yukon Gear Replacement Clutch Set For Dana 44 Powr Lok / Smooth |