Driveshaft 800HP Domestic Axle (RA8506X4) for a 2015-2017 Ford Mustang. DSS 2015 Mustang 800HP Direct-Fit Axle -Right RA8506X4.
Years | Make | Model | Trim | ||
---|---|---|---|---|---|
2015-2017 | Ford | Mustang | GT Premium | ||
2015-2017 | Ford | Mustang | Shelby GT350 | ||
2015-2017 | Ford | Mustang | GT | ||
2015-2015 | Ford | Mustang | GT 50 Years Limited Edition | ||
2015-2017 | Ford | Mustang | EcoBoost Premium | ||
2015-2017 | Ford | Mustang | Shelby GT350R | ||
2015-2017 | Ford | Mustang | EcoBoost | ||
2015-2017 | Ford | Mustang | V6 |
We have done all the calculations and pre-testing in machines and now its time to to send the new Level 4 design axles out and show how they work. The axles took a bit longer to make but we wanted to make sure the outcome was worth the wait. We had realized that a lot of people were buying the 1400HP axles that are unbelievable in strength but not exactly designed for a daily driven car. Sort of like a Drag Slick, great on the track and does what its supposed to but you would not go get groceries with them on a daily basis.
This new design axle is being made with the new 300M material we are getting out of Sweden, it has by far been the strongest material we have worked with to date and even though these axles are using the smaller 28 spline they were designed for better strength in mind. What was done 1st was we had the material Ground to the exact size we wanted and rolled the spline onto it (Rolled splines are 35% stronger than traditional cut style splines)
We then wanted to be able to go back to the Anti-Wheel hop design but know that one thicker bar would break and we wanted to take the time to figure out how to get an axle with more torsional resistance than a straight bar but not to the point that it caused an issue with it. After much work and testing we came up with this new design.
So there we have the completed product with new design outer mounting, ends are E-coated and the center of the axle Powder coated in our in house system. The CV will not only have a stronger or harder inner race but also have the Chromoly cage adding extra strength to the system. We have re-developed the Anti-Wheel hop design to be able to ensure the axles will help with the issue but also be higher torque friendly for cars that will punish them like they are bought for.
There are no reviews yet.
IN STOCK Ford Racing M-4130-MAFord Racing Axle Kits Ford Racing 2015-2017 Ford Mustang Half Shaft Upgrade Kit $2,480.82
|
IN STOCK Ford Racing M-4001-88355BFord Racing Differential Housings Ford Racing 2019 Ford Mustang Super 8.8in IRS Loaded Differential Housing 3.55 $1,283.77
|
IN STOCK Yukon Gear & Axle YG F8.8-411-15Yukon Gear & Axle Gear Sets - Ford Yukon Gear High Performance Gear Set for 2015+ Ford Mustang/F-150 8.8in in a 4.11 Ratio $426.89
|
IN STOCK - LOW McLeod Racing 6435825HDMcLeod Racing RXT Twin Clutch Kits McLeod RXT1200 Twin Power Pack W/ Billet Steel Flywheel 11-17 Ford Mustang 5.0L Coyote Clutch Kit $1,395.00
|
IN STOCK McLeod Racing 6337807MMcLeod Racing RXT Twin Clutch Kits McLeod RXT Clutch Kit 2016 Ford Mustang GT 350 w/ Aluminum Flywheel $1,750.00
|
IN STOCK McLeod Racing 6932-25McLeod Racing RXT Twin Clutch Kits McLeod RXT Clutch Mustang Coyote 1in X 23 Metric Spline 2011 Cars $955.00
|
IN STOCK McLeod Racing 139252McLeod Racing Clutch Lines McLeod Line Assy Mustang 2005-Up 36in W/Male Wire Clip Fittings & Elbow Bleeder $81.84
|
IN STOCK Ford Racing M-1104-BFord Racing Hub Kits Ford Racing 2015-2017 Ford Mustang Rear Wheel Hub Kit With ARP Studs $434.89
|
IN STOCK McLeod Racing 64388-25McLeod Racing RST Twin Clutch Kits McLeod RST Twin EcoBoost Mustang Sprung Hub w/ Steel Flywheel $1,274.00
|
For more information on Driveshaft Shop part number RA8506X4, you can visit the official Driveshaft Shop website.