South Bend Clutch K08028 SS DXD Stage 3 Clutch Kit
South Bend Clutch Stage 3 Clutch Kit (K08028 SS DXD) for a 1992-1993 Acura Integra 1.8 / L4. Stage 3 - Intended Use: DRAG - Torque Rating ft/lbs: 400.
|South Bend ST3 DRAG Clutch Kit For 92-93 Acura Integra 1.8L K08028-SS-DXD
ebay - Ends 03/12/2020
|South Bend / DXD Racing Clutch for 92-93 Acura Integra 1.8L Stg 3 Drag Clutch Ki
ebay - Ends 02/29/2020
See partnumber notes and applications notes above for specific product information.
STAGE 3 DAILY:
Recommended for single mass flywheel (SMF) when original design is DMF. This clutch package is designed for high HP vehicles desiring a start performance similar to O.E. The pressure plate is Race Engineered (SS) and SFI approved with significant load increase over stage 1,2 pressure plates (+600-800 lbs.). Expect a pedal effort increase of 20%-25%. Discs are assembled with heat-treated wear resistant hubs; drive plates and springs for high load transfer and dependable operation. The sprung centers on the disc in conjunction with the marcel fin between the linings create a dual dampening effect that simulates O.E. start performance. A Performance Organic friction material with a high metal content increases torque and RPM capability and maintains low operating temperatures which reduces wear and glazing.
Recommended usages are daily, spirited street and occasional track.
STAGE 3 ENDURANCE:
Recommended for single mass flywheel (SMF) when original design is DMF to achieve optimal performance. This kit uses the same Race Engineered SFI approved pressure plate as stage 3 daily package. The disc is designed for the special needs of a vehicle with circuit racing in mind. Kevlar friction material is used for its unique static to dynamic ratios of friction co-efficients at high energy levels. This translates to a perfect transition from one gear to the next. Discs are assembled with only performance components and equipped with torsion springs functioning as a damper between engine and gearbox.
Recommend usages are Rally, endurance race, clubsport, autocross, street and daily.
STAGE 3 DRAG:
Drag racing requires a Single Mass Steel Flywheel to be included with each kit when the original design is Dual Mass Flywheel. This clutch package is built to handle heavily modified cars and designed to function according to the specific needs of the 1/4 and 1/8 mile track. The pressure plate for this kit is SFI approved Race Cover engineered to disengage with less pedal travel shortening the shift time. Discs are a puck design, which reduces rotational mass and are assembled with all high carbon component pieces for maximum strength. The friction material used is Graphite impregnated Ceramic perfectly suited for drag racing because of its maximum friction co-efficient, rapid heat dissipation and abrupt engagement characteristics.
Recommended uses are drag, pulling, drifting.
WARNING: Cancer & Reproductive Harm www.p65warnings.ca.gov
There are currently no reviews. Be the first by reviewing below.
Write a Review:
Click here to contact us with your question regarding South Bend Clutch Stage 3 Clutch Kit (K08028 SS DXD).
- Clutch Masters Twin Disc 725 Series (08027-TD7R-S)
- Exedy Racing Stage 1 Organic Clutch Kit (08800A)
- ACT Sprung 4 Puck Clutch Kit (AI3-XXG4)
- ACT Sprung 6 Puck Clutch Kit (AI3-HDG6)
- Spec Stage 2 Clutch Kit (SA272)
- Spec Stage 1 Clutch Kit (SA271)
- Competition Clutch Stage 5 - Strip Series 1420 Clutch Kit (8027-1420)
- Competition Clutch Stock Replacement Clutch Kits (8027-STOCK)
- Clutch Masters FX500 Clutch Kit (08027-HRB6)
- Clutch Masters FX400 Clutch Kit (08027-HRC6)